1， Color: The color of the toilet bowl and the bathtub and the washbasin should be the same. The color should not be deeper than the floor tiles. The color should be coordinated with the wall tiles. 2, quality: the glazed surface of the toilet should be smooth and smooth, the color is crystal clear without obvious defects, can not have pinholes, lack of glaze, lightly hit the toilet to make it crisp and pleasing, no cracking sound is good, no cracks, the trademark should be clear, each The accessories are complete, and the appearance is free of deformation. 3， Water saving: The size of the water tank does not indicate whether it is water-saving type, but whether the design of the flushing and drainage system and the water tank fitting in the toilet structure is reasonable and the quality is passed. Generally, the toilet should be marked with the amount of flushing. When purchasing, you can request the test report of the relevant state department. Whether the water saving should be based on the report. The flushing volume below 6 liters can be listed as a water-saving toilet. 4, the water outlet: the outlet of the bathroom has the difference between the lower drainage and the horizontal drainage. The distance from the center of the water outlet to the wall behind the water tank should be measured. Otherwise, the toilet cannot be installed. The outlet of the horizontal drain toilet should be equal to the height of the horizontal drain, preferably slightly higher to ensure the smooth flow of sewage. 5, matching: three sets of sanitary ware must be matched, the relevant faucet should also be matched with the bathtub faucet, wash basin faucet, the same brand, the style is the same, if the conditions permit, the towel rack should also be the same type as the faucet. 6, wall distance: standard wall distance is generally divided into 305mm and 400mm two.
7， Drainage method: whether it is the lower row or the rear row. 8，Determine the drainage wall distance (pitch distance). 9， When selecting the toilet, observe whether the glaze of the toilet is uniform, whether there is any chromatic aberration and obvious deformation, and how the glossiness, surface defects (brown eyes, spots, cracks, orange glaze, ripples, spots, and dirty) can be strictly controlled. The glazed toilet is smooth, meticulous, and flawless. After repeated washing, it can still be as smooth as new. If the quality of the glaze is not good, it is easy to hang the dirt on the walls of the toilet. 10，Determine the water consumption. The water-saving toilet is less than or equal to 6 liters of water. The water storage capacity of the general toilet is adjustable, and the water consumption can be adjusted according to the characteristics of the family. 11, the toilet has a split and connected. Split toilets are generally small in size and suitable for bathrooms with small spaces. The one-piece toilet has a smooth line and a novel design, and there are many styles to choose from. 12， Look at the internal drain connections. If the gland and the content link are of poor quality, the toilet is both prone to fouling and water leakage. The gasket should be made of rubber or foamed plastic, which has large elasticity and good sealing performance. 13, look at the service. To choose a reputable branded product, many manufacturers offer free installation services.
Toilet purchase advice: 1，The flushing method is very important. The jet siphon is recommended because of its low noise, strong detergency and good visual appearance in the pit. 2, should choose a toilet with a moderate amount of water storage, too high water storage will splash ass, water storage is too low, easy to run. 3, pay attention to the glaze of the toilet, the quality of the toilet glazed surface should be smooth and smooth without blistering, saturated color. After checking the glazed surface of the outer surface, you should also touch the sewer of the toilet. If it is rough, it will be easy to be left behind. In addition, it is good to pay attention to the glaze. It is very good to clean in the future. Generally, the cheap ones are not good for the density and glaze of the porcelain. Soon the glaze will turn yellow, and it will not be washed anyway. The high-grade expensive is expensive in its porcelain dense glazed surface is not easy to corrode and wear. The high-grade toilet has reached the requirement of all-ceramicization because of the high temperature during firing, so it will feel heavy in the hand. The middle and low-grade toilets have a low firing temperature and a short time, so they do not meet the requirements for all-ceramics.